Series 18T  Precision T-Slot Milling Tip |
|
New Cutter Number |
Effective |
D1
Nominal Diameter |
Max. Radial
Depth Of Cut |
T1
Thread Size |
W
Width |
Corner Radius |
Torx
Driver |
New! 18T-5006TQRN00 |
6 |
.500 |
.09 |
T05 |
.062 |
.006 x 45 deg |
DS-T20T |
18T-5012TQRN01 |
6 |
.500 |
.09 |
T05 |
.125 |
.015 |
DS-T20T |
18T-6205T6RN02 |
6 |
.625 |
.13 |
T06 |
.056 |
.015 |
DS-T20T |
18T-6206T6RN01 |
6 |
.625 |
.13 |
T06 |
.062 |
.015 |
DS-T20T |
18T-6206T6RN02 |
6 |
.625 |
.13 |
T06 |
.068 |
.015 |
DS-T20T |
18T-6208T6RN01 |
6 |
.625 |
.13 |
T06 |
.078 |
.015 |
DS-T20T |
18T-6208T6RN02 |
6 |
.625 |
.13 |
T06 |
.086 |
.015 |
DS-T25T |
18T-6210T6RN01 |
6 |
.625 |
.13 |
T06 |
.105 |
.015 |
DS-T25T |
18T-6212T6RN01 |
6 |
.625 |
.13 |
T06 |
.125 |
.015 |
DS-T25T |
18T-6216T6RN01 |
6 |
.625 |
.13 |
T06 |
.156 |
.015 |
DS-T25T |
18T-7516T8RN01 |
6 |
.750 |
.13 |
T08 |
.156 |
.015 |
DS-T30T |
18T-7519T8RN01 |
6 |
.750 |
.13 |
T08 |
.187 |
.015 |
DS-T30T |
18T-7525T8RN01 |
6 |
.750 |
.13 |
T08 |
.250 |
.015 |
DS-T30T |
18T-8718T8RN01 |
6 |
.875 |
.19 |
T08 |
.187 |
.015 |
DS-T40T |
18T-8725T8RN01 |
6 |
.875 |
.19 |
T08 |
.250 |
.015 |
DS-T40T |
18T-8731T8RN01 |
6 |
.875 |
.19 |
T08 |
.312 |
.015 |
DS-T40T |
18T-10037TRRN01 |
6 |
1.00 |
.19 |
T10 |
.375 |
.015 |
DS-T50T |
|
 |
| Series 18T - Front/Back Chamfer, V-Form Tip |
|
New Cutter Number |
Effective |
D1
Nominal Diameter |
A |
T1
Thread Size |
W
Width |
Corner Chamfer |
Torx
Driver |
18T-6216T6RN06 |
6 |
.625 |
.030 |
T06 |
.156 |
45 degree x .062" |
DS-T20T |
|
|
T-Slotter Operating Guidelines |
|
Material |
Spec |
Hardness Brinnel |
SFM |
Feed per Tooth |
Coolant |
Aluminum |
7075 - T6, 6061 - T6, 2024 |
- |
1650-2500 |
.0025-.0035 |
Yes |
Cast Iron
|
Gray |
150-250 |
350-550 |
.0025-.0035 |
No
|
Nodular |
150-250 |
425-650 |
.0030-.0040 |
Steel
|
Low Carbon 1018, 8620 |
150-250 |
450-750 |
.0025-.0035 |
No
|
High Carbon F-6180 |
250-400 |
250-450 |
.0030-.0040 |
Alloyed Steel 4140, 4340 |
150-300 |
350-550 |
|
Tool Steel A-6, D-1, D-2 |
Up to 300 |
350-450 |
|
Stainless Steel
|
300 Series, 304, 316 |
- |
300-500 |
.0025-.0035 |
may not be required at high speeds |
400 Series 15-5 PH |
Up to 320 |
250-400 |
.0030-.0040 |
may not be required at high speeds |
13-8 PH |
- |
200-350 |
|
Yes |
Nickel Alloys |
Inconel, Hastelloy, Waspalloy |
- |
100-200 |
.0025-.0035 |
Yes |
Titanium |
6AL-4V |
- |
150-200 |
.0025-.0035 |
Yes |
Please see Ingersoll's Milling Products Catalog (CAT-001) for chip thinning factor application at various depths of cut |
|
