Series: TSC
Representative image shown ⓘ
The image above is intended to represent the product series for illustrative purposes only. The actual product may vary.
Product Series Features:
- Pressed Single-Ended Insert
- For Parting & Deep Grooving
- C-Type Chipbreaker
Part Number |
SSC Insert Seat Size |
CW Cutting Width |
RE Corner Radius |
WB Body Width |
INSL Insert Length |
PSIRR Cutting Edge Angle Major Right Hand |
PSIRL Cutting Edge Angle Major Left Hand |
S1 Thickness |
DAXIN Axial Groove I.D. Min. |
DMIN Min. Bore Dia. |
FEEDGN Grooving Feed Min. |
FEEDGX Grooving Feed Max. |
|
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| TSC2 | 2 | 0.079 | 0.008 | 0.067 | 0.790 | - | - | 0.185 | 29.330 | 1.575 | 0.002 | 0.007 | |
| TSC2-15L | 2 | 0.079 | 0.008 | 0.067 | 0.790 | - | 15 | 0.185 | 29.330 | 1.575 | 0.002 | 0.005 | |
| TSC2-15LS | 2 | 0.079 | 0.001 | 0.067 | 0.770 | - | 15 | 0.185 | 29.330 | 1.575 | 0.001 | 0.005 | |
| TSC2-15R | 2 | 0.079 | 0.008 | 0.067 | 0.790 | 15 | - | 0.185 | 29.330 | 1.575 | 0.002 | 0.007 | |
| TSC2-15RS | 2 | 0.079 | 0.001 | 0.067 | 0.770 | 15 | - | 0.185 | 29.330 | 1.575 | 0.001 | 0.005 | |
| TSC2-6L | 2 | 0.079 | 0.008 | 0.067 | 0.790 | - | 6 | 0.185 | 29.330 | 1.575 | 0.002 | 0.006 | |
| TSC2-6R | 2 | 0.079 | 0.008 | 0.067 | 0.790 | 6 | - | 0.185 | 29.330 | 1.575 | 0.002 | 0.006 | |
| TSC2-8R | 2 | 0.079 | 0.008 | 0.067 | 0.790 | 8 | - | 0.185 | 29.330 | 1.575 | 0.002 | 0.006 | |
| TSC3 | 3 | 0.118 | 0.008 | 0.094 | 0.790 | - | - | 0.185 | 2.126 | 1.968 | 0.003 | 0.010 | |
| TSC3-15L | 3 | 0.118 | 0.008 | 0.094 | 0.790 | - | 15 | 0.185 | 2.126 | 1.968 | 0.002 | 0.006 | |
| TSC3-15R | 3 | 0.118 | 0.008 | 0.094 | 0.790 | 15 | - | 0.185 | 2.126 | 1.968 | 0.002 | 0.006 | |
| TSC3-15RS | 3 | 0.118 | 0.001 | 0.094 | 0.770 | 15 | - | 0.185 | 2.126 | 1.968 | 0.001 | 0.006 | |
| TSC3-6L | 3 | 0.118 | 0.008 | 0.094 | 0.790 | - | 6 | 0.185 | 2.126 | 1.968 | 0.002 | 0.007 | |
| TSC3-6R | 3 | 0.118 | 0.008 | 0.094 | 0.790 | 6 | - | 0.185 | 2.126 | 1.968 | 0.002 | 0.007 | |
| TSC4 | 4 | 0.157 | 0.012 | 0.118 | 0.790 | - | - | 0.185 | 1.339 | 1.968 | 0.003 | 0.012 | |
| TSC4-15R | 4 | 0.157 | 0.012 | 0.118 | 0.790 | 15 | - | 0.185 | 1.339 | 1.968 | 0.002 | 0.009 | |
| TSC4-4L | 4 | 0.157 | 0.012 | 0.118 | 0.790 | - | 4 | 0.185 | 1.339 | 1.968 | 0.002 | 0.009 | |
| TSC4-4R | 4 | 0.157 | 0.012 | 0.118 | 0.790 | 4 | - | 0.185 | 1.339 | 1.968 | 0.002 | 0.009 | |
| TSC5 | 5 | 0.197 | 0.012 | 0.157 | 0.980 | - | - | 0.205 | 1.930 | 2.362 | 0.004 | 0.014 | |
| TSC5-4R | 5 | 0.197 | 0.012 | 0.157 | 0.980 | 4 | - | 0.205 | 1.930 | 2.362 | 0.003 | 0.011 | |
| TSC6 | 6 | 0.236 | 0.012 | 0.197 | 0.980 | - | - | 0.205 | 1.811 | 2.362 | 0.005 | 0.016 | |
| TSC8 | 8 | 0.315 | 0.016 | 0.236 | 0.980 | - | - | 0.205 | 1.260 | 2.756 | 0.006 | 0.017 |
Parting and Grooving Chip Breakers
- 1st choice for general use in parting and deep grooving
- Stable cutting edge & interrupted cut
- Medium-to-high feed
- For carbon steel, alloy steel and cast iron
- For hard materials
- 1st choice for soft materials in parting and deep grooving
- Sharp cutting edge & low cutting force
- Low-to-medium feed
- Tubes, small diameter and thin-wall parts
- For stainless steel & low carbon steel
- For heat resistant super alloy
- Sharp cutting edge and wide groove with minimized burrs
- For tubes of small size workpieces
- For stainless steel and mild steel
- Narrow chip breaker
- Good chip control in low feed of ductile materials and low-carbon steel
- For Cr-Ni alloy steel and bearing steel
