Tool Holding

Driver Bits

Standard Driver Bit
Hex, Torx, and Torx Plus drive options
NOTE: Images shown are a representation of the product series only and may not be an actual representation of each specific product within the series

Torque Test Bar

Torque Test Bar for Hydraulic Chuck
Optional Accessory Item - Sold separately

Chip-Surfer
C*T

C-Adapter (ISO 26623-1)
Chip Surfer "T" Style Thread Connection
Neck Relief
Quick Change Holder
AD Style with Ported Coolant delivery
Note: Do not apply lubricant to the threaded connection.

Chip-Surfer
C*T (Metric)

C-Adapter (ISO 26623-1)
Chip Surfer "T" Style Thread Connection
Neck Relief
Quick Change Holder
AD Style with Ported Coolant delivery
Note: Do not apply lubricant to the threaded connection.

Chip-Surfer
CHIP SURFER Torque Wrench

Pre-Set Torque Wrench Handle with Replaceable Thin Open End Wrench Head that fits Chip Surfer tip wrench flats
No lubricant on adaption
Optional Accessory Item

Chip-Surfer
CHIP SURFER Torque Wrench Head

Replaceable Thin Open End Wrench Head that fits Chip Surfer tip wrench flats
No lubricant on adaption
Optional Accessory Item
NOTE: Replaceable Head only - for complete assembly see CHIP SURFER Torque Wrench

Chip-Surfer
DIN69871*T (Metric)

DIN69871 V-Flange
Chip Surfer "T" Style Thread Connection
AD Style Coolant (coolant through the center)
Balanced G2.5@20,000 RPM

Chip-Surfer
ER*T - Solid ER, Neck Relief

Solid ER
Chip Surfer "T" Style Thread Connection
Neck Relief
Coolant Options

Chip-Surfer
HSKA*T

HSK-A (DIN 69893/A)
Chip Surfer "T" Style Thread Connection
Balanced G2.5@20,000 RPM
AD Style Coolant
Note: A cooling tube is required for use with all coolant through HSK spindles and should be purchased separately

Chip-Surfer
HSKA*T (Metric)

HSK-A (DIN 69893/A)
Chip Surfer "T" Style Thread Connection
Balanced G2.5@20,000 RPM
AD Style Coolant
Note: A cooling tube is required for use with all coolant through HSK spindles and should be purchased separately

Chip-Surfer
S*T*CA - Carbide Shank, Necked

Cylindrical Shank
Chip Surfer "T" Style Thread Connection
Neck Relief
Shank modifications can be made by cutting off the back to desired length or turning back neck for more usable length

Chip-Surfer
S*T*CA - Carbide Shank, Necked (Metric)

Cylindrical Shank
Chip Surfer "T" Style Thread Connection
Neck Relief
Coolant options
Shank modifications can be made by cutting off the back to desired length or turning back neck for more usable length

Chip-Surfer
S*T*CA - Carbide Shank, No Neck

Cylindrical Shank
Chip Surfer "T" Style Thread Connection
No Neck Relief
Due to tolerance, shank diameter will be slightly larger than tip diameter. .010" per side neck modification required for clearance when milling 90° shoulder

Chip-Surfer
S*T*CA - Carbide Shank, No Neck (Metric)

Cylindrical Shank
Chip Surfer "T" Style Thread Connection
No Neck Relief
Coolant options
Due to tolerance, shank diameter will be slightly larger than tip diameter. .010" per side neck modification required for clearance when milling 90° shoulder

Chip-Surfer
S*T*CK - Carb. Shank, Cone Neck (Metric)

Cylindrical Shank
Chip Surfer "T" Style Thread Connection
Conical Neck

Chip-Surfer
S*T*CK - Carbide Shank, Cone Neck

Cylindrical Shank
Chip Surfer "T" Style Thread Connection
Conical Neck

Chip-Surfer
S*T*HA - Heavy Metal Shank, No Neck

Cylindrical Shank
Chip Surfer "T" Style Thread Connection
No Neck Relief
Due to tolerance, shank diameter will be slightly larger than tip diameter. .010" per side neck modification required for clearance when milling 90° shoulder

Chip-Surfer
S*T*HA - Hvy Mtl Shank, Necked (Metric)

Cylindrical Shank
Chip Surfer "T" Style Thread Connection
Neck Relief
Coolant options
Shank modifications can be made by cutting off the back to desired length or turning back neck for more usable length

Chip-Surfer
S*T*HK - Heavy Metal, Cone Neck (Metric)

Cylindrical Shank
Chip Surfer "T" Style Thread Connection
Conical Neck
Coolant options

Chip-Surfer
S*T*NA - Steel Shank, Thrust Cool

Cylindrical Shank
Chip Surfer "T" Style Thread Connection
Neck Relief
Thrust Cool System equipped with brazed Coolant Collar and Coolant Grooves for precise delivery down the Neck OD to the tip's cutting edges
Thrust Cool Shanks are ideal for use with carbide tips that do not have coolant holes

Chip-Surfer
S*T*SA - Steel Shank, Necked

Cylindrical Shank
Chip Surfer "T" Style Thread Connection
Neck Relief
Shank modifications can be made by cutting off the back to desired length or turning back neck for more usable length

Chip-Surfer
S*T*SA - Steel Shank, Necked (Metric)

Cylindrical Shank
Chip Surfer "T" Style Thread Connection
Neck Relief
Coolant options
Shank modifications can be made by cutting off the back to desired length or turning back neck for more usable length

Chip-Surfer
S*T*SA - Steel Shank, No Neck

Cylindrical Shank
Chip Surfer "T" Style Thread Connection
No Neck Relief
Due to tolerance, shank diameter will be slightly larger than tip diameter. .010" per side neck modification required for clearance when milling 90° shoulder

Chip-Surfer
S*T*SA - Steel Shank, No Neck (Metric)

Cylindrical Shank
Chip Surfer "T" Style Thread Connection
No Neck Relief
Coolant options
Due to tolerance, shank diameter will be slightly larger than tip diameter. .010" per side neck modification required for clearance when milling 90° shoulder

Chip-Surfer
S*T*SA - Steel Weldon, Necked (Metric)

Weldon Shank
Chip Surfer "T" Style Thread Connection
Stubby Neck Relief

Chip-Surfer
S*T*SK - Steel Shank, Cone Neck

Cylindrical Shank
Chip Surfer "T" Style Thread Connection
Conical Neck

Chip-Surfer
S*T*SK - Steel Shank, Cone Neck (Metric)

Cylindrical Shank
Chip Surfer "T" Style Thread Connection
Conical Neck

Chip-Surfer
S_T_K - Steel Weldon, Cone Neck (Metric)

Cylindrical Shank with Flat
Chip Surfer "T" Style Thread Connection
Conical Neck

Chip-Surfer
T_T_S - Extension

Chip Surfer "T" Style Thread Connection
Neck Relief

Chip-Surfer
W*T*SA - Steel Weldon, Necked

Weldon Shank
Chip Surfer "T" Style Thread Connection
Stubby Neck Relief

Chip-Surfer
WB_T_K - Steel Weldon, Cone Neck

Cylindrical Shank with Flat
Chip Surfer "T" Style Thread Connection
Conical Neck

Chip-Surfer
Wrench CHIP SURFER

Thin Open End Wrenches for use with Chip Surfer tips
Do not use lubricant on adaption
When assembling, be sure tip is seated firmly on shank with no
Optional Accessory Item
Tip should seat firmly on shank with no gap when assembling

Inno-Fit
BT*Z*SA

BT MAS-403 Spindle Adapter
Innofit Heavy Duty Modular Adaption
AD Style Coolant
Strong drive pin design with 3-point clamping & self-centering connections
Change cutter heads right on the spindle
Resists bending forces uniformly
Transmits axial forces from cut-to-spindle
Complete with sealing & tensioning screws

Inno-Fit
CAT*Z*SA

CAT Spindle Adapter
Innofit Heavy Duty Modular Adaption
AD Style Coolant
Strong drive pin design with 3-point clamping & self-centering connections
Change cutter heads right on the spindle
Resists bending forces uniformly
Transmits axial forces from cut-to-spindle
Complete with sealing & tensioning screws

Inno-Fit
DIN69871*Z*SA

DIN 69871 Form AD Spindle Adapter
Innofit Heavy Duty Modular Adaption
AD Style Coolant
Strong drive pin design with 3-point clamping & self-centering connections
Change cutter heads right on the spindle
Resists bending forces uniformly
Transmits axial forces from cut-to-spindle
Complete with sealing & tensioning screws

Inno-Fit
HSKA*Z*SA

HSK-A (DIN 69893/A) Spindle Adapter
Innofit Heavy Duty Modular Adaption
Coolant Through (Coolant Tube required)
Strong drive pin design with 3-point clamping & self-centering connections
Change cutter heads right on the spindle
Resists bending forces uniformly
Transmits axial forces from cut-to-spindle
Complete with sealing & tensioning screws

Inno-Fit
Z*MOD*SK

InnoFit to Top On Adapter
TopOn Adapter for the modular InnoFit System
Coolant Through
Interchangeable with Inch and Metric Heads

Inno-Fit
Z*SM*SA

INCH Face Mill Adapter for the modular InnoFit system
Interchangeable with Inch and Metric heads
Coolant Through except where noted

Inno-Fit
Z*SM*SA (Metric)

METRIC Face Mill Adapter for the modular InnoFit system
Interchangeable with Inch and Metric heads
Coolant Through

Inno-Fit
Z*Z*SA

Extensions for Innofit Modular System
Strong Drive Pin Design with 3 Point Clamping
Self Centering Connections
Interchangeable with Inch and Metric heads
Coolant Through

Inno-Fit
Z5Z4SA

Reducing Adapter for the Innofit Modular System
Strong Drive Pin Design with 3 Point Clamping
Self Centering Connections
Interchangeable with Inch and Metric heads
Coolant Through

IT.TE.DI.
BT Face Mill Holder

MAS 403
For Metric and Inch Face Mills

IT.TE.DI.
CAT Face Mill Holder

For Metric and Inch Face Mills

IT.TE.DI.
HSK Face Mill Holder

HSK (DIN 69893)
For Metric and Inch Face Mills

MultiSurfer
S*L*SA - Steel Shank

Cylindrical Shank
MultiSurfer "L" Style Thread Connection
Ideal for Facing tips
Shank modifications can be made by cutting off the back to desired length or turning back neck for more usable length
Strong and precise Pilot, Screw & Tri-Lobe Drive Connection

MultiSurfer
S*L*SA - Steel Shank (Metric)

Cylindrical Shank
MultiSurfer "L" Style Thread Connection
Ideal for Facing tips
Shank modifications can be made by cutting off the back to desired length or turning back neck for more usable length
Strong and precise Pilot, Screw & Tri-Lobe Drive Connection

MultiSurfer
S*L*SA - Steel Shank, Necked

Cylindrical Shank
MultiSurfer "L" Style Thread Connection
Neck Relief
Ideal for slotting and threading tips
Shank modifications can be made by cutting off the back to desired length or turning back neck for more usable length
Strong and precise Pilot, Screw & Tri-Lobe Drive Connection

MultiSurfer
S*L*SA - Steel Shank, Necked (Metric)

Cylindrical Shank
MultiSurfer "L" Style Thread Connection
Neck Relief
Ideal for slotting and threading tips
Shank modifications can be made by cutting off the back to desired length or turning back neck for more usable length
Strong and precise Pilot, Screw & Tri-Lobe Drive Connection

Qwik-Torque
QWIK*TORQUE SYSTEM

Interchangeable multi-component system consisting of handle, preset torque bit, & torx bit
Magnetic locking adaption
Reversible system in unit enables both tightening & loosening of screws
Radial friction design & non-ratchet torque socket prevents overtightening & stripping of screws
Life cycle of approximately 20,000 operations
Compatible with 1/4" hex drive bits

T-Absorber Bars
C*DT*A*D

C-Adapter (ISO 26623-1)
Quick Change Serrated ConnectionShanks for T-Absorber Interchangeable Heads
300 Bar Max PSI

T-Absorber Bars
C*DT*D*TB (Metric)

C-Adapter (ISO 26623-1)
Quick Change Adapter for T-Absorber Anti-Vibration Tools
100 Bar Max PSI

T-Absorber Bars
C*DT*E*D

C-Adapter (ISO 26623-1)
Quick Change Serrated ConnectionShanks with Carbide Core for T-Absorber Interchangeable Heads
300 Bar Max PSI

T-Micro Holders
MINS

Single ended T-Micro sleeve

T-Micro Holders
MINS (Metric)

Single ended T-Micro sleeve

T-Micro Holders
MINSL

Double ended T-Micro sleeve
All sleeves applicable for Citizen Swiss type machine

T-Micro Holders
MINSL (Metric)

Double ended T-Micro sleeve
All sleeves applicable for Citizen Swiss type machine

Tool Holders
ADJBT*ER

BT MAS-403
Center Alignment ER Collet Chuck DIN 6499
AD Style Coolant (Coolant through the Center)
For use with Qwik Ream & Unidex Tooling
Radial adjustment 0.05 mm
Angular adjustment 1°

Tool Holders
ADJC*ER

C-Adapter (ISO 26623-1)
Center Alignment ER Collet Chuck DIN 6499
Quick Change Holder
For use with Qwik Ream & Unidex Tooling
Radial adjustment .002"
Angular adjustment 1°

Tool Holders
ADJCAT*ER

CAT V-Flange
Center Alignment ER Collet Chuck DIN 6499
Coolant through the Center
For use with Qwik Ream & Unidex Tooling
AD Style Coolant (coolant through the center)
Radial adjustment .002"
Angular adjustment 1°

Tool Holders
ADJDIN69871*ER

DIN69871 V-Flange
Center Alignment ER Collet Chuck DIN 6499
For use with Qwik Ream & Unidex Tooling
AD Style Coolant (Coolant through the Center)
Radial adjustment 0.05mm
Angular adjustment 1°

Tool Holders
ADJHSKA*ER

HSK-A (DIN 69893/A)
Center Alignment ER Collet Chuck DIN 6499
Quick Change Holder
For use with Qwik Ream & Unidex Tooling
Radial adjustment .002"
Angular adjustment 1°

Tool Holders
ADJST*ER

INCH Weldon Shank
Center Alignment ER Collet Chuck DIN 6499
Quick Change Tool Holder
For use with Qwik Ream & Unidex Tooling
Radial adjustment .008"
Angular adjustment 1°
Central Coolant Hole

Tool Holders
ADJST*ER (Metric)

METRIC Weldon Shank
Center Alignment ER Collet Chuck DIN 6499
Quick Change Holder
For use with Qwik Ream & Unidex Tooling
Radial adjustment .008"
Angular adjustment 1°
Central coolant hole

Tool Holders
BT*EM

BT MAS-403
INCH Weldon End Mill Holder DIN 6359/DIN 1835 Form B
AD Style Coolant (coolant through the center)

Tool Holders
BT*EM (Metric)

BT MAS-403
METRIC Weldon End Mill Holder DIN 6359/DIN 1835 Form B
AD Style Coolant (coolant through the center)

Tool Holders
BT*EM*E (Metric)

BT MAS-403
Whistle Notch End Mill/Drill Holder DIN6359/1835 Form E
AD Style Coolant (coolant through the center)

Tool Holders
BT*ER

BT MAS-403
ER Collet Chuck DIN6499
AD Style Coolant (coolant through the center)
Balanced G6.3@12,000RPM
(Note: Some BT40 holders under 100 mm GL are balanced G2.5@20,000 RPM)

Tool Holders
BT*ER*SHORT

BT MAS-403
ER Short Collet Chuck DIN 6499
Balanced G2.5@20,000RPM
AD Style Coolant (coolant through the center)

Tool Holders
BT*FC*EM

BT MAS-403 Face Contact
INCH Weldon End Mill Holder DIN 1835 Form B
AD Style Coolant (coolant through the center)
Balanced G2.5@25,000RPM

Tool Holders
BT*FC*EM (Metric)

BT MAS-403 Face Contact
METRIC Weldon End Mill Holder DIN 1835 Form B
AD Style Coolant (coolant through the center)

Tool Holders
BT*FC*ER

BT MAS-403 Face Contact
ER Collet Chuck DIN 6499
ADB Convertible through the center or through the flange coolant delivery
BT40 balanced G2.5@20,000RPM
BT50 balanced G2.5@15,000RPM

Tool Holders
BT*FC*FM (Metric)

BT MAS-403 Face Contact
METRIC Face Mill Holder DIN 6357
AD Style Coolant except where noted
BT40 balanced G2.5@20,000RPM
BT50 balanced G2.5@15,000RPM
Note: 60mm Pilot is 4-Bolt pattern adaption only with no lock screw. 40mm Pilot has 4-Bolt pattern and lock screw adaption
*Peripheral clamping screws are not supplied with holder

Tool Holders
BT*FC*MAXIN (Metric)

BT MAS-403 Face Contact
METRIC Power Milling Chuck
Chucking forces will be reduced by 25% when reduction sleeves are used
Optional reduction sleeves should be ordered separately
*Note: Preset screws are compatible with milling chuck sleeves only, they are not compatible for use with the holder alone

Tool Holders
BT*FC*SEM*C

BT MAS-403 Face Contact
INCH Shell Mill Holder with Coolant Holes ISO 3937
AD Style Coolant with coolant ports at the base of the pilot
Balanced G2.5@20,000RPM

Tool Holders
BT*FC*SEM*C (Metric)

BT MAS-403 Face Contact
METRIC Shell Mill Holder with Coolant Holes ISO 3937
AD Coolant with coolant ports at the base of the pilot
BT30 & BT40 balanced G2.5@20,000RPM
BT50 balanced G2.5@15,000RPM

Tool Holders
BT*FC*SRKIN (Metric)

BT MAS-403 Face Contact
METRIC Thermal Shrink Chucks
AD Style Coolant (coolant through the center)
BT40 balanced G2.5@20,000RPM
BT50 balanced G2.5@15,000RPM
For use in Induction style heating units only

Tool Holders
BT*FM

BT MAS-403
INCH Face Mill Holder DIN 6357
AD Style Coolant except where noted

Tool Holders
BT*FM (Metric)

BT MAS-403
METRIC Face Mill Holder DIN 6357
AD Style Coolant except where noted
**Note: 60mm Pilot is 4-Bolt pattern adaption only with no lock screw. 40mm Pilot has 4-Bolt pattern and lock screw adaption

Tool Holders
BT*HYDRO (Metric)

BT MAS-403
METRIC Hydraulic Milling Chuck
BT30 - AD Style Coolant (Coolant thru Center)
BT40/BT50 - ADB Style Coolant (coolant thru center or flange)
BT30/BT40 balanced G6.3@12,000 RPM
BT50 balanced G6.3@8,000 RPM
Note: Chucking forces will be reduced by 25% when using reduction sleeves

Tool Holders
BT*MAXIN

BT MAS-403
INCH Power Milling Chuck
Chucking forces will be reduced by 25% when reduction sleeves are used
Optional reduction sleeves should be ordered separately
*Note: Preset screws are compatible with milling chuck sleeves only, they are not compatible for use with the holder alone

Tool Holders
BT*MAXIN (Metric)

BT MAS-403
METRIC Power Milling Chuck
Chucking forces will be reduced by 25$% when reduction sleeves are used
Optional reduction sleeves should be ordered separately
*Note: Preset screws are compatible with milling chuck sleeves only, they are not compatible for use with the holder alone

Tool Holders
BT*SEM

BT MAS-403
INCH Shell Mill Holder ISO 3937
AD Style Coolant

Tool Holders
BT*SEM (Metric)

BT MAS-403
METRIC Shell Mill Holder ISO 3937
AD or ADB Style Coolant as noted

Tool Holders
BT*SEM*C (Metric)

BT MAS-403
METRIC Shell Mill Holder with Coolant Holes ISO 3937
ADB Style Coolant with coolant ports at the base of the pilot
BT40 balanced G2.5 @ 20,000 RPM
BT50 balanced G2.5 @ 15,000 RPM

Tool Holders
BT*SEMC (Metric)

BT MAS-403
METRIC Combi Shell Mill Holder
AD Style Coolant

Tool Holders
BT*SRK (Metric)

BT MAS-403
METRIC Thermal Shrink Chuck
AD Style Coolant (coolant through the center)
Balanced G2.5@25,000RPM

Tool Holders
BT*SRKIN

BT MAS-403
INCH Thermal Shrink Chuck
AD Style Coolant (coolant through the center)
For use with Inductive Heating devices ONLY
-C Indicates coolant ports in nose
BT40 balanced G2.5@25,000RPM

Tool Holders
BT*SRKIN (Metric)

BT MAS-403
METRIC Thermal Shrink Chuck
AD Style Coolant (coolant through the center)
For use with Inductive Heating Device ONLY
BT40 balanced G2.5@25,000RPM
BT50 balanced G2.5@20,000RPM

Tool Holders
BT*STUB

BT MAS-403
INCH Slotting Cutter Stub Arbor
For use with axial drive cutters

Tool Holders
C*ABB

C-Adapter (ISO 26623-1)
Quick Change Adapter for Boring Bars with Reducing Sleeves
1450 PSI Max

Tool Holders
C*ABB (Metric)

C-Adapter (ISO 26623-1)
Quick Change Adapter for Boring Bars with Reducing Sleeves
1450 PSI Max

Tool Holders
C*ABB*C (Metric)

C-Adapter (ISO 26623-1)
Quick Change Adapter for Boring Bars with Reducing Sleeves
Ported Coolant Delivery
1450 PSI Max

Tool Holders
C*AD*BT

BT MAS-403
C-Adapter (ISO 26623-2)
Quick Change Adapter
AD Style Coolant (coolant though the center) except where noted as ABD Style

Tool Holders
C*AD*CAT

CAT V-Flange
C-Adapter (ISO 26623-2)
Quick Change Adapter
AD Style Coolant (coolant through the center) except where noted as ABD Style Coolant

Tool Holders
C*AD*HSKA

HSK-A (DIN 69893/A)
C-Adapter (ISO 26623-2)
Quick Change Adapter

Tool Holders
C*AD*SK (DIN 69871)

DIN69871 (SK) V-Flange
C-Adapter (ISO 26623-2)
Quick Change Adapter
AD Style Coolant (coolant through the center) except where noted as ABD Style Coolant

Tool Holders
C*ADE (Metric)

C-Adapter (ISO 26623-1)
Quick Change Holder for METRIC External Square Shank Tools
100 Bar Max PSI

Tool Holders
C*ADI (Metric)

C-Adapter (ISO 26623-1)
Quick Change Adapter for Boring Bars
100 Bar Max

Tool Holders
C*ASHA (Metric)

C-Adapter (ISO 26623-1)
Quick Change Perpendicular holder for External Square Shank Tools
100 Bar Max PSI

Tool Holders
C*ASHR/L

C-Adapter (ISO 26623-1)
Quick Change Holder for INCH External Square Shank Tools
1450 PSI Max

Tool Holders
C*ASHR/L (Metric)

C-Adapter (ISO 26623-1)
Quick Change Holder for METRIC External Square Shank Tools
100 Bar Max PSI

Tool Holders
C*ASHR/L-45 (Metric)

C-Adapter (ISO 26623-1)
Quick Change Holder for METRIC External Square Shank Tools
For 45° Mounting on Turn Mill Machines
100 Bar Max

Tool Holders
C*EM

C-Adapter (ISO 26623-1)
INCH Weldon Shank End Mill Holder
Per DIN 1835 Form B
Quick Change Holder

Tool Holders
C*EM (Metric)

C-Adapter (ISO 26623-1)
METRIC Weldon Shank End Mill Holder
Per DIN1835 Form B
Quick Change Holder

Tool Holders
C*EM*E (Metric)

C-Adapter (ISO 26623-1)
METRIC Whistle Notch End Mill / Drill Holder
Quick Change Holder
Per DIN6359/DIN1835 Form E

Tool Holders
C*ER

C-Adapter (ISO 26623-1)
ER Collet Chuck DIN 6499
Quick Change Holder

Tool Holders
C*ER*M

C-Adapter (ISO 26623-1)
ER Long Mini Nut Style Collet Chuck
Per DIN 6499
Quick Change Holder

Tool Holders
C*EX*C

C-Adapter (ISO 26623-1)
C-Adapter (ISO 26623-2)
Quick Change Extension
NOTE: Extensions do not have the Data Chip Provision slot

Tool Holders
C*FM (Metric)

C-Adapter (ISO 26623-1)
METRIC Face Mill Holder DIN 6357
Quick Change Holder
Note: Peripheral clamping screws are not supplied with the holder

Tool Holders
C*MAXIN

C-Adapter (ISO 26623-1)
INCH MAXIN Power Milling Chuck
Quick Change Holder
Chucking forces will be reduced by 25% when reduction sleeves are used
Optional reduction sleeves should be ordered separately
*Note: Preset screws are compatible with milling chuck sleeves only, they are not compatible for use with the holder alone

Tool Holders
C*MAXIN (Metric)

C-Adapter (ISO 26623-1)
METRIC MAXIN Power Milling Chuck
Quick Change Holder
Chucking forces will be reduced by 25% when reduction sleeves are used
Optional reduction sleeves should be ordered separately
*Note: Preset screws are compatible with milling chuck sleeves only, they are not compatible for use with the holder alone

Tool Holders
C*RE*C

C-Adapter (ISO 26623-1)
C-Adapter (ISO 26623-2)
Quick Change Reducer
NOTE: Reducers do not have the Data Chip Provision slot

Tool Holders
C*SEM*C

C-Adapter (ISO 26623-1)
INCH Shell Mill Holder with Internal Coolant Holes ISO 3937
Quick Change Holder

Tool Holders
C*SEM*C (Metric)

C-Adapter (ISO 26623-1)
METRIC Shell Mill Holder with Internal Coolant Holes ISO 3937
Quick Change Holder

Tool Holders
C*SEMC (Metric)

C-Adapter (ISO 26623-1
METRIC Combi Shell Mill Holder
Quick Change Holder

Tool Holders
C*SRKIN

C-Adapter (ISO 26623-1)
INCH Thermal Shrink Chuck
Quick Change Holder
For use with h6 carbide, steel, or HSS shank tooling
For use with Induction style heating units only

Tool Holders
C*SRKIN (Metric)

C-Adapter (ISO 26623-1)
INCH Thermal Shrink Chuck
Quick Change Holder
For use with h6 carbide, steel, or HSS shank tooling
For use with Induction style heating units only

Tool Holders
C*TBK (Metric)

C-Adapter (ISO 26623-1)
Quick Change Block for Parting & Grooving Blades

Tool Holders
C*TBU (Metric)

C-Adapter (ISO 26623-1)
Quick Change Block for Parting & Grooving Blades

Tool Holders
CAT*EM

CAT V-Flange
INCH Weldon Style End Mill Holder DIN 6359/1835 Form B
AD Style Coolant (coolant through the center)

Tool Holders
CAT*EM-M (Metric)

CAT V-Flange
METRIC Weldon Shank End Mill Holder DIN 6359/1835 Form B
AD Style Coolant (coolant through the center)

Tool Holders
CAT*ER

CAT V-Flange
ER Collet Chuck DIN 6499
AD Style Coolant (coolant through the center)
CAT30 / CAT40 balanced G2.5@20,000RPM
CAT50 balanced G2.5@12,000RPM

Tool Holders
CAT*ER*SHORT

CAT V-Flange
ER Short Collet Chuck DIN 6499
AD Style Coolant (coolant through the center)
Balanced G2.5 @ 20,000 RPM

Tool Holders
CAT*FC*EM

CAT Face Contact
INCH Weldon End Mill Holder DIN 1835 Form B
AD Style Coolant (coolant through the center)

Tool Holders
CAT*FC*ER

CAT Face Contact
ER Collet Chuck DIN 6499
AD Style Coolant (coolant through the center)
AD Style Coolant (through the center)
CAT40 balanced G2.5@20,000RPM
CAT50 balanced G2.5@15,000RPM

Tool Holders
CAT*FC*MAXIN

CAT Face Contact
MAXIN Power Milling Chuck
Chucking forces will be reduced by 25% when reduction sleeves are used
Optional reduction sleeves should be ordered separately
*Note: Preset screws are compatible with milling chuck sleeves only, they are not compatible for use with the holder alone

Tool Holders
CAT*FC*SEM*C

CAT Face Contact
INCH Shell Mill Holder with Internal Coolant Holes ISO 3937
Symmetrical Design, Dynamically Balanced for high RPM Machining
AD Style Coolant with coolant ports at the base of the pilot
Balanced G2.5 @ 20,000 RPM

Tool Holders
CAT*FC*SRKIN

CAT Face Contact
Thermal Shrink Chuck
AD Style Coolant (coolant through the center)
For use with Carbide, HSS, and Steel tools with h6 tolerance
Balanced G2.5@25,000RPM
For use with Inductive Heating devices only

Tool Holders
CAT*FM

CAT V-Flange
INCH Face Mill Adapter
AD Style Coolant
Note: 4" and 6" Gage Lengths are standard with both the 4 Bolt Circle Pattern and Lock Screw adaptions, 2.875" Gage Length has 4 Bolt Circle adaption only
*Peripheral clamping screws are not supplied with holder

Tool Holders
CAT*HYDRO

CAT V-Flange
Hydraulic Milling Chuck
ADB Style Coolant (converible coolant through the center or flange)
CAT40 Balanced G2.5@18,000 RPM
CAT50 Balanced G2.5@12,000 RPM
Recommended for chatter dampening when machining high temperature alloys such as titanium
Chucking forces will be reduced by 25% if reduction sleeves (optional) are used.

Tool Holders
CAT*MAXIN

CAT V-Flange
MAXIN Power Milling Chuck
Chucking forces will be reduced by 25% when reduction sleeves are used
Optional reduction sleeves should be ordered separately
*Note: Preset screws are compatible with milling chuck sleeves only, they are not compatible for use with the holder alone

Tool Holders
CAT*SEM

CAT V-Flange
INCH Shell Mill Holder ISO 3937

Tool Holders
CAT*SEM*C

CAT V-Flange
INCH Shell Mill Holder with Internal Coolant Holes ISO 3937
Symmetrical Design, Dynamically Balanced for high RPM Machining
ADB Style Coolant with coolant holes at the base of the pilot
Balanced G2.5@20,000RPM

Tool Holders
CAT*SRK

CAT V-Flange
Thermal Shrink Chuck
AD Style Coolant (coolant through the center)
Balanced G2.5@25,000RPM

Tool Holders
CAT*SRKIN

CAT V-Flange
Thermal Shrink Chuck
ADB Style Coolant (convertible coolant through the center & flange)
For use with Inductive Heating device ONLY
Balanced G2.5@25,000RPM

Tool Holders
CAT*STUB

CAT V-Flange
INCH Slotting Cutter Stub Arbor
For use with Axial drive cutters

Tool Holders
Coolant Lock Screw Set - Inch

Adjustable protrution nozzle directs coolant to the cutting zone
Improves chip evacuation
Nozzle screw position can be secured by a locking nut
Can be easily adjusted according to countersink depth, insert size, etc
Set includes nozzle screw, locking screw, locking nut, and washers

Tool Holders
Coolant Lock Screw Set - Metric

Adjustable protrution nozzle directs coolant to the cutting zone
Improves chip evacuation
Can be easily adjusted according to countersink depth, insert size, etc
Nozzle screw position can be secured by a locking nut
Set includes nozzle screw, locking screw, locking nut, and washers

Tool Holders
Cooling Tube

Cooling Tube
Required for use with all coolant through HSK and C-Adapter Spindles
Optional Accessory Item - Sold separately

Tool Holders
DIN*MAXIN

DIN6971 V-Flange
MAXIN Power Milling Chuck
Chucking forces will be reduced by 25% when reduction sleeves are used
Optional reduction sleeves should be ordered separately
*Note: Preset screws are compatible with milling chuck sleeves only, they are not compatible for use with the holder alone

Tool Holders
DIN69871*FM (Metric)

DIN69871 Form A/AD Shank
METRIC Face Mill Holder DIN 6357
AD Style Coolant except where noted
Note: 60mm Pilot is 4-Bolt pattern adaption only with no lock screw. 40mm Pilot has 4-Bolt pattern and lock screw adaption
*Peripheral clamping screws are not supplied with holder

Tool Holders
DIN69871*SEM (Metric)

DIN69871 Form AD
METRIC Shell Mill Holder ISO 3937

Tool Holders
DIN69871*SEM*C (Metric)

DIN69871 Form ADB
METRIC Shell Mill Holder with Internal Coolant Holes ISO 3937
ADB Style Coolant with Coolant Ports in pilot face
Symmetrical Design
Dynamically balanced for high RPM machining
DIN69871-40 Balanced G2.5 @ 20,000 RPM
DIN69871-50 Balanced G2.5 @ 15,000 RPM

Tool Holders
DIN69871*SEMC (Metric)

DIN69871 Form AD
METRIC Combi Shell Mill Holder DIN 6358
AD Style Coolant

Tool Holders
ECCENTRIC SLEEVE

Eccentric Sleeve for enlarging or reducing nominal drilling diameters
Note: The pin, or allen wrench, required to facilitate radial adjustment of the sleeve is not included

Tool Holders
ECCENTRIC SLEEVE (Metric)

Eccentric Sleeve for enlarging or reducing metric nominal drilling diameters
Note: The pin, or allen wrench, required to facilitate radial adjustment of the sleeve is not included

Tool Holders
ER*EX

ER Series DIN6499 Spring Collet
Single Diameter
.0004" Runout Tolerance
Recommended for improved runout & clamping torque.

Tool Holders
ER*EX*AA

ER Series DIN6499 Spring Collet
Single Diameter
.0002" Runout Tolerance
Super Finish Surface with Special Anti-Corrosion protection
Recommended for improved runout & clamping torque.

Tool Holders
ER*SEAL*AA

ER Series DIN 6499/ISO15488-B Rubber Sealed Collet
Single Diameter Inch
8 Slot Design
Collaspe Range 0.008" Max
Super Finish Surface with Anti-Corrosion protection
.0002" TIR
For up to 1450 PSI

Tool Holders
ER*SEAL*AA (Metric)

ER Series DIN 6499/ISO15488-B Rubber Sealed Collet
Single Diameter Metric
8 Slot Design
Collaspe Range 0.2 mm Max
Super Finish Surface with Anti-Corrosion protection
.0002" TIR
For up to 1450 PSI

Tool Holders
ER*SEAL*AA JET

DIN 6499/ISO 15488-B ER JET Sealed Collet
4 Cooling Jets direct coolant flow to the cutting edge
8 Slot Rubber Sealed design
For use with standard straight shank cutting tools (without coolant holes) only
Single Diameter with maximum 0.008" collapse range
AA High Precision Grade - .0002" TIR
Anti-Corrosion Protected
For up to 1450 PSI

Tool Holders
ER*SEAL*AA JET (Metric)

DIN 6499/ISO 15488-B ER JET Metric Sealed Collet
4 Cooling Jets direct coolant flow to the cutting edge
8 Slot Rubber Sealed design
For use with standard straight shank cutting tools (without coolant holes) only
Single Diameter with maximum 0.2 mm collapse range
AA High Precision Grade - 0.005 mm TIR
Anti-Corrosion Protected
For up to 1450 PSI

Tool Holders
ER*SPR

ER Series DIN 6499 /ISO15488-B Spring Collet
Inch/Metric Combination
Hard Touch Coated
.0004" TIR
NOTE: ER11 COLLETS SHOWN WITH .039" (1 mm) CLAMPING RANGE HAVE BEEN PHASED OUT AND REPLACED WITH .020" (0.5 mm) CLAMPING RANGE

Tool Holders
ER*SPR*AA

ER Series DIN 6499-AA Spring Collet
Inch/Metric Combination
Ultra Precision .0002" TIR
Hard Touch coated

Tool Holders
ER*SRK

INCH ER Series Integral Collet
Thermal Shrink Adaption
For use with Carbide Shank Tooling only
Max PSi = 1450

Tool Holders
ER*SRK (Metric)

METRIC ER Series Integral Collet
Thermal Shrink Adaption
For use with Carbide Shank tooling ONLY
Max PSi = 1450

Tool Holders
ER*SRK*JET2

INCH ER Series Integral Collet with Internal Cooling Jets
Thermal Shrink Adaption
Max PSi = 1450
For use with standard carbide shank (non-coolant through) tooling only

Tool Holders
ER*SRK*JET2 (Metric)

METRIC ER Series DIN 6499 Integral Collet
Thermal Shrink Adaption
2 Internal Cooling Jets
For use with standard carbide shank (non-coolant through) tooling
Max PSi 1450 / 100 BAR
*Note: When assembled in an ER holder, the actual protruding length of the holder becomes shorter by 2.0 mm for ER20 and 3.0 mm for ER25 and ER32

Tool Holders
ER11SPR*AA

ER11 Series DIN 6499-AA Spring Collet
Ultra Precision .0002" TIR
Hard Touch coated

Tool Holders
ER11SRK (Metric)

Metric ER Series Integral Collet
Thermal Shrink Adaption
100 Bar Max
For use with carbide shank tooling ONLY
**NOTE: ER11SRK should be used only with TYPHOON spindles

Tool Holders
HSKA*EM

HSK DIN69893 Form A
INCH Weldon End Mill Holder DIN6355/DIN1835 Form B

Tool Holders
HSKA*ER

HSK-A (DIN 69893/A)
ER Collet Chuck DIN6499
HSK A40-A63 balanced G2.5@20,000RPM
HSK A100 balanced G6.3@12,000RPM

Tool Holders
HSKA*ER*M

HSK-A (DIN 69893/A)
ER Mini Collet Chuck DIN6499
HSK A50-A63 Balanced G2.5@20,000RPM
HSK A100 balanced G6.3@12,000RPM

Tool Holders
HSKA*ER*SHORT

HSK-A (DIN 69893/A)
ER Short Collet Chuck DIN 6499
Balanced G2.5@20,000RPM

Tool Holders
HSKA*FM

HSK-A (DIN 69893/A)
INCH Face Mill Holder DIN 6353
4 Bolt Adaption Pattern (No Lock Screw on Pilot)
Note: Peripheral clamping screws are not included with holder

Tool Holders
HSKA*FM (Metric)

HSK-A (DIN 69893/A)
METRIC Face Mill Holder DIN 6353
4 Bolt Adaption Pattern (No Lock Screw on Pilot)
Balanced G2.5@33,000RPM
Note: Peripheral clamping screws are not included with holder

Tool Holders
HSKA*HYDRO

HSK-A (DIN 69893/A)
INCH Hydraulic Milling Chuck
HSKA50-A63 balanced G2.5@25,000RPM
HSKA100 balanced G2.5@18,000RPM
Note: Chucking forces will be reduced by 25% if reduction sleeves (optional) are used.

Tool Holders
HSKA*HYDRO (Metric)

HSK-A (DIN 69893/A)
METRIC Hydraulic Milling Chuck
HSKA63 balanced G2.5@24,000RPM
HSKA80 balanced G2.5@16,000RPM
HSKA100 balanced G2.5@15,000RPM
Note: Chucking forces will be reduced by 25% if reduction sleeves (optional) are used.

Tool Holders
HSKA*MAXIN

HSK-A (DIN 69893/A)
INCH Power Milling Chuck
Chucking forces will be reduced by 25% when reduction sleeves are used
Optional reduction sleeves should be ordered separately
*Note: Preset screws are compatible with milling chuck sleeves only, they are not compatible for use with the holder alone

Tool Holders
HSKA*MAXIN (Metric)

HSK-A (DIN 69893/A)
METRIC Power Milling Chuck
Chucking forces will be reduced by 25% when reduction sleeves are used
Optional reduction sleeves should be ordered separately
*Note: Preset screws are compatible with milling chuck sleeves only, they are not compatible for use with the holder alone

Tool Holders
HSKA*SEM

HSK-A (DIN 69893/A)
INCH Shell Mill Holder ISO 3937
HSK A50- A63 balanced G2.5@15,000RPM
HSK A100 balanced G6.3@12,000RPM

Tool Holders
HSKA*SEM (Metric)

HSK-A (DIN 69893/A)
METRIC Shell Mill Holder ISO 3937
HSK A50- A63 balanced G2.5@15,000RPM
HSK A100 balanced G6.3@12,000RPM

Tool Holders
HSKA*SEM*C

HSK-A (DIN 69893/A)
INCH Shell Mill Holder with Internal Coolant Holes ISO 3937
Symmetrical Design for high RPM Machining
Heavy Duty Drive Keys for higher torque transfer
4 Coolant Ports spaced 90° apart on face of pilot
Balanced - HSKA63 G2.5@20,000RPM / HSK A100 G2.5@15,000RPM

Tool Holders
HSKA*SEM*C (Metric)

HSK-A (DIN 69893/A)
METRIC Shell Mill Holder with Internal Coolant Holes ISO 3937
Symmetrical Design for high RPM Machining
Heavy Duty Drive Keys for higher torque transfer
4 Coolant Ports spaced 90° apart on face of pilot
Balanced - HSKA63 G2.5@20,000RPM / HSK A100 G2.5@15,000RPM

Tool Holders
HSKA*SEMC (Metric)

HSK-A (DIN 69893/A)
METRIC Combi Shell Mill Holder DIN 6358
AD Style Coolant
Balanced G2.5 @ 15,000 RPM
*Axial Drive Key not included
For Axial Drive use, remove driving ring and use Axial Drive Key with Spacer Rings

Tool Holders
HSKA*SRK

HSK-A (DIN 69893/A)
INCH Thermal Shrink Chuck
For use with Carbide shank tooling ONLY
Balanced G2.5@25,000RPM

Tool Holders
HSKA*SRK (Metric)

HSK-A (DIN 69893/A)
METRIC Thermal Shrink Chuck
Balanced G2.5@25,000RPM
For use with Carbide shank tooling ONLY

Tool Holders
HSKA*SRKIN

HSK-A (DIN 69893/A)
INCH Thermal Shrink Chuck
For use with carbide, HSS, and steel shank tooling
HSKA63 balanced G2.5@25,000RPM
HSKA100 balanced G2.5@20,000 RPM

Tool Holders
HSKA*SRKIN (Metric)

HSK-A (DIN 69893/A)
METRIC Thermal Shrink Chuck
For use with carbide, HSS, and steel h6 shank tooling
HSKA63 balanced G2.5@25,000RPM
HSKA100 balanced G2.5@20,000RPM

Tool Holders
HSKE*ER

HSK-E (DIN 69893/E)
ER Collet Chuck DIN 6499
Balanced G2.5@25,000RPM

Tool Holders
HSKE*SEM

HSK-E (DIN 69893/E)
INCH Shell Mill Holder ISO 3937
Balanced G2.5@15,000RPM

Tool Holders
HSKE*SEM (Metric)

HSK-E (DIN 69893/E)
METRIC Shell Mill Holder ISO 3937
Balanced G2.5@15,000RPM

Tool Holders
HSKE*SRK

HSK-E (DIN 69893/E)
INCH Thermal Shrink Chuck
Balanced G2.5@25,000 RPM
*For use with Carbide shank tooling ONLY

Tool Holders
HSKE*SRK (Metric)

HSK-E (DIN 69893/E)
METRIC Thermal Shrink Chuck
Balanced G2.5@25,000 RPM
*For use with Carbide shank tooling ONLY

Tool Holders
HSKFM*SEM

HSK-FM (DIN 69893/F)
INCH Shell Mill Holder ISO 3937
For use on Makino models MAG Series A machines
Balanced G2.5@33,000 RPM
Note: Orientation pins can be removed for use as a standard HSK F spindle adaption

Tool Holders
HSKFM*SEM (Metric)

HSK-FM (DIN 69893/F)
METRIC Shell Mill Holder ISO 3937
For use on Makino models MAG Series A machines
Balanced G2.5@33,000RPM
Note: Orientation pins can be removed for use as a standard HSK F spindle adaption

Tool Holders
HSKFM*SRKIN

HSK-FM (DIN 69893/F)
INCH Thermal Shrink Chuck with removeable Drive Pins for use on Makino models MAG Series A
HSK FM balanced G2.5@33,000RPM
For use with caribide, HSS, & steel tools with h6 shank tolerance
Note: Compatible with inductive heating devices only

Tool Holders
INDER11TOOLADAPTER

ER11 Series Thermal Shrink Adapter
To be used with the INDER32TOOLADAPTER on inductive heating device

Tool Holders
Nut ER MINI/UM

ER MINI/UM Clamping Nut
For use with DIN 6499 Collet chucks
ER MINI Nuts are slotted style nuts
ER16 UM and ER20 UM are Hex style nuts
ER25, ER32, ER40, and ER50 are slotted style nuts
Hard Lube Coating for extended life

Tool Holders
Nut ER SHORT

ER SHORT Clamping Nut
For Use with ER*SHORT Collet Chucks Only
Threaded OD for short projection

Tool Holders
Nut ER TOP

ER TOP Clamping Nut
DIN 6499 Collet Chucks
Exclusive Anti-Friction Mechanism
Combination Flush/Power Nut
Hard Touch Protective Coating
Power gripping force with unique compact standard DIN 6499 design
ER16/ER20 Hex Style
ER25/ER32/ER40 Slotted Style

Tool Holders
Pre-Set Screws

Preset Screws
*Note: Images shown are a generic representation of the product and may not be an actual representation of each specific product within the series

Tool Holders
R8*ER

R8 Bridgeport Shank
ER Collet Chuck DIN 6499

Tool Holders
Retention Knob Sockets

For use with installation of retention knobs and pull studs
Aids in prevention of rounded off corners
Extends life span of the retention knob
Manufactured using AISI 4150 Steel
Made in the USA
Optional Accessory Item

Tool Holders
SC*HYDRO

INCH Sealed Reduction Sleeve
For use in hydraulic milling chucks
Note: Sleeves are compatible with all cylindrical shanks and Weldon shanks .250"-.750" diameter
**Sleeves are not recommended for use with Weldon shanks over .750" diameter

Tool Holders
SC*HYDRO (Metric)

METRIC Sealed Reduction Sleeve
For use in hydraulic milling chucks
Note: Sleeves are compatible with all cylindrical shanks and flatted shanks 6-20 mm diameter
**Sleeves are not recommended for use with flatted shanks over 20 mm diameter

Tool Holders
SC*SEAL

Inch Straight Sealed Sleeve/Collet
For use with MAXIN Power Milling Chucks
Preset Screw available for tool positioning (Sold Separately)
*Chucking forces will be reduced by 25% when the optional reduction sleeves are used

Tool Holders
SC*SEAL (Metric)

Metric Straight Sealed Sleeve/Collet
For use with MAXIN Power Milling Chucks
Preset Screw available for tool positioning (Sold Separately)
*Chucking forces will be reduced by 25% when the optional reduction sleeves are used

Tool Holders
SC*SPR

INCH Straight Sleeve
For use with MAXIN Power Milling chucks
Preset Screw available for tool positioning (Sold Separately)
Note: Chucking forces will be reduced by 25% when the optional reduction sleeves are used

Tool Holders
SC*SPR (Metric)

Metric Straight Sleeve/Collet
For use with MAXIN Power Milling Chucks
Preset Screw available for tool positioning (Sold Separately)
*Chucking forces will be reduced by 25% when the optional reduction sleeves are used

Tool Holders
SC*SPR INCH/METRIC

INCH to METRIC Straight Sleeve
For use with Power Milling Chucks
Note: Chucking forces will be reduced by 25% when the optional reduction sleeves are used

Tool Holders
SET ER*SEAL*AA

ER Series DIN 6499/ISO15488-B Sealed Collet
Single Diameter Inch Set
Super Finish Surface with Anti-Corrosion protection
8 Slot Design
Increased rigidity, higher accuracy, and better clamping force
.0002" TIR
For up to 1450 PSI

Tool Holders
SET ER*SEAL*AA (Metric)

ER Series DIN 6499/ISO15488-B Sealed Collet
Single Diameter Metric Set
Super Finish Surface with Anti-Corrosion protection
8 Slot Design
Increased rigidity, higher accuracy, and better clamping force
.0002" TIR
For up to 1450 PSI

Tool Holders
SET ER*SEAL*AA JET

ER-AA Sealed JET Inch Collet Set
DIN 6499/ISO 15488-B
8 Slot Design with 4 Cooling Jets
Single Diameter with max .008" Collapse range
Anti-Corrosion Protection
Up to 1450 PSI
Runout tolerance of .0002"
For use with non-coolant through tooling only

Tool Holders
SET ER*SEAL*AA JET (Metric)

ER-AA Sealed JET Metric Collet Set
DIN 6499/ISO 15488-B
8 Slot Design with 4 Cooling Jets
Single Diameter with 0.2 mm Max Collapse range
Anti-Corrosion Protection
Up to 1450 PSI
Runout tolerance of 0.005 mm
For use with non-coolant through tooling only

Tool Holders
SET ER*SPR

SET ER DIN 6499 Collets
Inch/Metric Combination
Hard Touch coated for improved accuracy and wear resistance
Runout tolerance of .0004"

Tool Holders
SET ER*SPR*AA

SET ER-AA DIN 6499 Collets
Inch/Metric Combination
Ultra Precision .0002" run out tolerance
Hard Touch coated for improved accuracy & wear resistance

Tool Holders
SET ER*SPR*EM (Metric)

ER DIN 6499 Collet Set
METRIC End Mill Shank Sizes
Hard Touch coated for improved accuracy and wear resistance
Runout tolerance of .0004"

Tool Holders
SET ER*SPR*EM AA (Metric)

ER DIN 6499 Collet Set
METRIC End Mill Shank Sizes
Hard Touch coated for improved accuracy and wear resistance
Runout tolerance of .0002"

Tool Holders
SET ER*SPR*EX AA

ER DIN 6499 Collet Set
Single Diameter INCH size
Hard Touch coated for improved accuracy and wear resistance
Runout tolerance of .0002"

Tool Holders
SET SC*SEAL

Set Inch Straight Sealed Sleeve/Collets
For use with MAXIN Power Milling Chucks
Preset Screw available for tool positioning (Sold Separately)
*Chucking forces will be reduced by 25% when the optional reduction sleeves are used

Tool Holders
SET SC*SEAL (Metric)

Set Metric Straight Sealed Sleeve/Collets
For use with MAXIN Power Milling Chucks
Preset Screw available for tool positioning (Sold Separately)
*Chucking forces will be reduced by 25% when the optional reduction sleeves are used

Tool Holders
SET SC*SPR

Set Inch Straight Sleeve/Collets
For use with MAXIN Power Milling Chucks
Preset Screw available for tool positioning (Sold Separately)
*Chucking forces will be reduced by 25% when the optional reduction sleeves are used

Tool Holders
SET SC*SPR (Metric)

Set Metric Straight Sleeve/Collets
For use with MAXIN Power Milling Chucks
Preset Screw available for tool positioning (Sold Separately)
*Chucking forces will be reduced by 25% when the optional reduction sleeves are used

Tool Holders
ST*ER

INCH Cylindrical Shank
ER Collet Chuck DIN 6499
Central Coolant Hole

Tool Holders
ST*ER*M

INCH Cylindrical Shank
ER Collet Chuck DIN 6499
Central Coolant Hole

Tool Holders
ST*ER*MF

INCH Cylindrical Flatted Shank
ER Collet Chuck DIN 6499 with Mini Nut
For Use on Swiss Type CNC Lathe
Central Coolant Hole

Tool Holders
ST*ER*MFD

INCH Cylindrical Flatted Shank
ER Collet Chuck DIN 6499 Double Ended with Mini Nut
Central Coolant Hole

Tool Holders
ST*ER*S

INCH Cylindrical Shank
ER Collet Chuck DIN 6499 with 1/4" NPT inlet
Central coolant hole

Tool Holders
ST*SRK

INCH Cylindrical Shank
Thermal Shrink Holder
For use with carbide shank tooling only
Central Coolant Hole

Tool Holders
ST*SRK (Metric)

METRIC Cylindrical Shank
Thermal Shrink Holder
For use with carbide shank tooling only
Central Coolant Hole

Tool Holders
Tool Holder Lock Screws

*Note: Images shown are a generic representation of the product and may not be an actual representation of each specific product within the series

Tool Holders
Wrench COMBI Spanner

DIN6368 Wrench
For use with Metric Face and COMBI Shell Mill Holder Lock Screw
Optional Accessory Item

Tool Holders
Wrench Cooling Tube C-Adapter

Cooling Tube Wrench for C-Adapter Series Holders
T-Handle Wrench used for Coolant Tube installation and removal in C-Adapter style holders
Optional Accessory Item

Tool Holders
Wrench Cooling Tube HSK

Cooling Tube Wrench for HSK Holders
T-Handle Wrench used for Coolant Tube installation and removal in HSK style holders
Optional Accessory Item

Tool Holders
Wrench ER

Wrench for ER DIN 6499 Collet Nut
Optional Accessory Item

Tool Holders
Wrench MAXIN

Wrench for MAXIN Milling Chuck
Optional Accessory Item

Tool Holders
Wrench TOP ON

Metric Thin Head Check Nut Wrench
Single End 15 Degree Angled Slotted Opening
For Use with Top On Tooling
Drop Forged from Steel Bar
Industrial Black Coating
Optional Accessory Item

Top-On
BT*ODP

BT MAS-403
TopOn Threaded Depo Adaption
BT40 balanced G2.5@20,000RPM
BT50 balanced G6.3@12,000RPM
ADB Style Convertible Coolant (coolant through the center or flange)
Note: Remove plug screw from flange to activate coolant through the flange delivery option

Top-On
BT*ODP (Metric)

BT MAS-403
TopOn Threaded Depo Adaption
BT40 balanced G2.5@20,000RPM
BT50 balanced G6.3@12,000RPM
ADB Style Convertible Coolant (coolant through the center or flange)
Note: Remove plug screw from flange to activate coolant through the flange delivery option

Top-On
C*ODP

C-Adapter (ISO 26623-1)
TopOn Threaded Depo Adaption
Quick Change Holder with Data Chip Slot
Balanced G6.3@15,000RPM
Note: A cooling tube is required for use with all coolant through
C-Adapter spindles and should be purchased separately

Top-On
C*ODP (Metric)

C-Adapter (ISO 26623-1)
TopOn Threaded Depo Adaption
Quick Change Holder with Data Chip Slot
Balanced G6.3@15,000RPM
Note: A cooling tube is required for use with all coolant through
C-Adapter spindles and should be purchased separately

Top-On
CAT40*ODP

CAT40 V-Flange
TopOn Threaded Depo Adaption
Balanced G2.5@20,000 RPM
ADB Convertible Coolant (Through the center or flange)
Note: Remove screw from flange to activate coolant through the flange delivery option

Top-On
CAT50*ODP

CAT50 V-Flange
TopOn Threaded Depo Adaption
Balanced G6.3@12,000 RPM
ADB Convertible Coolant (Through the center or flange)
Note: Remove plug screw from flange to activate teh coolant through the flange delivery option

Top-On
CDPER*M

TopOn Threaded Adaption Adapter
ER Collet Chuck DIN 6499
Interchangeable with inch and metric shanks
Coolant through center feedhole

Top-On
CDPER*M (Metric)

TopOn Threaded Adaption Adapter
ER Collet Chuck DIN 6499
Interchangeable with Inch and Metric Shanks
Coolant through Center

Top-On
CDPM*SRK

TopOn Threaded Adaption Adapter
INCH Thermal Shrink Fit Chuck
Coolant through center feedhole
Interchangeable with inch and metric shanks
For use with carbide shank tooling only

Top-On
CDPM*SRK (Metric)

TopOn Threaded Adaption Adapter
METRIC Thermal Shrink Fit Chuck
Coolant through center feedhole
Interchangeable with inch and metric shanks
For use with carbide shank tooling only

Top-On
DIN69871*ODP (Metric)

DIN 69871 V-Flange
TopOn Threaded Depo Adaption
CAT40 Balanced G2.5@20,000 RPM
CAT50 Balanced G6.3@12,000 RPM
ADB Convertible Coolant (Through the center or flange)
Note: Remove screws in flange to activate flange coolant option

Top-On
ER*ODP

ER Style Integral Collet
TopOn Threaded Adaption Adapter
JET2 Style Ported Coolant
Max 1450 psi
For use with standard straight shank tooling

Top-On
HSKA*ODP

HSK-A (DIN69893/A)
TopOn Threaded Depo Adaption
HSKA63 balanced G2.5@20,000 RPM
HSKA100 Balanced G6.3@12,000 RPM
Note: A cooling tube is required for use with all coolant through HSK spindles and should be purchased separately

Top-On
HSKA*ODP (Metric)

HSK-A (DIN69893/A)
TopOn Threaded Depo Adaption
HSKA63 balanced G2.5@20,000 RPM
HSKA100 Balanced G6.3@12,000 RPM
Note: A cooling tube is required for use with all coolant through HSK spindles and should be purchased separately

Top-On
HSKE*ODP

HSK-E (DIN 69893/E)
TopOn Threaded Depo Adaption
Balanced G2.5@20,000 RPM
Note: A cooling tube is required for use with all coolant through HSK spindles and should be purchased separately

Top-On
HSKE*ODP (Metric)

HSK-E (DIN 69893/E)
TopOn Threaded Depo Adaption
Balanced G2.5@20,000 RPM
Note: A cooling tube is required for use with all coolant through HSK spindles and should be purchased separately

Top-On
MOD*MOD*SA

TopOn Threaded Adaption Extension
Central Coolant Hole

Top-On
MOD*MOD*SK

TopOn Threaded Adaption Reducer
Central Coolant Hole

Top-On
MOD*SEM*C

TopOn Thread Adaption Adapter
INCH Shell Mill Holder ISO 3937
Coolant ports at base of pilot
Note: When mounting TopOn threaded adaptions to their holders, the mating surfaces & threaded areas must be thoroughly cleaned. Apply appropriate tightening torque to eliminate gap between mating surfaces.

Top-On
MOD*SEM*C (Metric)

TopOn Thread Adaption Adapter
METRIC Shell Mill Holder ISO 3937
Coolant ports at base of pilot
Note: When mounting TopOn threaded adaptions to their holders, the mating surfaces & threaded areas must be thoroughly cleaned. Apply appropriate tightening torque to eliminate gap between mating surfaces.

Top-On
MOD*T*SK

TopOn Threaded Depo Adaption Adapter
Chip Surfer "T" Style Thread Connection
Coolant through the center
*See Notes below

Top-On
S*MOD*CA

Inch Cylindrical Carbide Shank
TopOn Depo Thread Adaption
Central Coolant Hole
Interchangeable with Inch and Metric milling heads
Enables machining with larger overhang
Useful in deep cavity machining applications

Top-On
S*MOD*CA (Metric)

Metric Cylindrical Carbide Shank
TopOn Threaded Depo Adaption
Central Coolant Hole
Interchangeable with Inch and Metric milling heads
Enables machining with larger overhang
Useful in deep cavity machining applications

Top-On
S*MOD*CK

Inch Conical Taper Carbide Shank
TopOn Threaded Depo Adaption
Central Coolant Hole
Interchangeable with Inch and Metric milling heads
Enables machining with larger overhang
Useful in deep cavity machining applications

Top-On
S*MOD*CK (Metric)

Metric Conical Taper Carbide Shank
TopOn Threaded Depo Adaption
Central Coolant Hole
Interchangeable with Inch and Metric milling heads
Enables machining with larger overhang
Useful in deep cavity machining applications

Top-On
S*MOD*HA (Metric)

Metric Straight Cylindrical Heavy Metal Shank
TopOn Threaded Depo Adaption
Central Coolant Hole
Interchangeable with Inch and Metric milling heads
Enables machining with larger overhang
Useful in deep cavity machining applications

Top-On
S*MOD*HK (Metric)

Metric Straight Conical Heavy Metal Shank
TopOn Threaded Depo Adaption
Central Coolant Hole
Interchangeable with Inch and Metric milling heads
Enables machining with larger overhang
Useful in deep cavity machining applications

Top-On
S*MOD*SA

Inch Cylindrical Steel Shank
TopOn Threaded Depo Adaption
Central Coolant Hole
Interchangeable with Inch and Metric milling heads
Enables machining with larger overhang
Useful in deep cavity machining applications

Top-On
S*MOD*SA (Metric)

Metric Cylindrical Steel Shank
TopOn Threaded Depo Adaption
Central Coolant Hole
Interchangeable with Inch and Metric milling heads
Enables machining with larger overhang
Useful in deep cavity machining applications

Top-On
S*MOD*SK

Inch Conical Taper Steel Shank
TopOn Threaded Depo Adaption
Central coolant feedhole
Interchangeable with inch and metric milling heads
Enables machining with larger overhang
Useful in deep cavity machining applications

Top-On
S*MOD*SK (Metric)

Metric Conical Taper Steel Shank
TopOn Threaded Depo Adaption
Central Coolant Hole
Interchangeable with Inch and Metric milling heads
Enables machining with larger overhang
Useful in deep cavity machining applications

Top-On
S*MOD*VA (Metric)

Metric Straight Cylindrical Anti Vibe Shank
TopOn Threaded Depo Adaption
Central Coolant Hole
Interchangeable with Inch and Metric milling heads
Enables machining with larger overhang
Useful in deep cavity machining applications

Top-On
W*MOD*SA

Cylindrical Steel Flatted Shank
Depo Thread Adaption
Central Coolant Hole
Interchangeable with Inch and Metric milling heads
Enables machining with larger overhang
Useful in deep cavity machining applications

Top-On
W*MOD*SK

Conical Steel Flatted Shank
Depo Thread Adaption
Central Coolant Hole
Interchangeable with Inch and Metric milling heads
Enables machining with larger overhang
Useful in deep cavity machining applications

Turning Sleeves
QSL

Sleeve for T-Absorber anti-vibration boring bars
Flat surface for clamping to the machine's tool holder
One-sided slit for robust clamping force and high precision

Turning Sleeves
QSL (Metric)

Metric sleeve for metric T-Absorber anti-vibration boring bars
Flat surface for clamping to the machine's tool holder
One-sided slit for robust clamping force and high precision

Turning Sleeves
SC*T

INCH Reduction Sleeve
For use in holders with exchangeable adaption
-B indicates non-threaded access hole

Turning Sleeves
SC*T (Metric)

METRIC Reduction Sleeve
For use in holders with exchangeable adaption
-B indicates non-threaded access hole

Turning Sleeves
TSL

C-type sleeves, inch to metric

Turning Sleeves
TSL T-Mini (Metric)

Sleeves for T-mini boring bars, metric to metric

Turning Sleeves
TSL T-Mini-I

Sleeves for t-mini boring bars, inch to metric

Turning Sleeves
TSL-I

C-type sleeves, inch to inch

Turning Sleeves
TSL-M (Metric)

C-type sleeves, metric to metric

Typhoon
TJS PARTS & ACCESSORIES

Typhoon Spindle Spare Parts & Accessories
Compatible with all GJET and HPC Typhoon Spindles
All items are included with the purchase of a Typhoon Spindle unless otherwise noted as being sold separately.

Typhoon
Typhoon TJS*GJET*BT

BT MAS-403
Coolant driven high speed compact spindle
For use with small diameter tools on limited-RPM machines
Rotational Speeds of 35-55KRPM
Required Coolant Pressure 290-580psi
Maximum Tool Shank Diameter .276"/7mm
For use in finish & semi-finish applications
Balanced G2.5 @ 60,000 rpm
Bluetooth display required for operation (Sold Separately)

Typhoon
Typhoon TJS*GJET*C#

C-Adapter (ISO 26623-1)
Coolant Driven High Speed Compact Spindle
For use with small diameter tools on limited-RPM machines
Rotational Speeds of 35-55KRPM
Required Coolant Pressure 290-580psi
Maximum Tool Shank Diameter .276"/7mm
For use in finish & semi-finish applications
Balanced G2.5 @ 60,000 rpm
Bluetooth display required for operation (Sold Separately)

Typhoon
Typhoon TJS*GJET*CAT

CAT V-Flange
Coolant Driven High Speed Compact Spindle
For use with small diameter tools on limited-RPM machines
Rotational Speeds of 35-55KRPM
Required Coolant Pressure 290-580psi
Maximum Tool Shank Diameter .276"/7mm
For use in finish & semi-finish applications
Balanced G2.5 @ 60,000 rpm
Bluetooth display required for operation (Sold Separately)

Typhoon
Typhoon TJS*GJET*ER32

ER32 DIN6499
Coolant Driven High Speed Compact Spindle
For use with small diameter tools on limited-RPM machines
Rotational Speeds of 35-55KRPM
Required Coolant Pressure 290-580psi
Maximum Tool Shank Diameter .276"/7mm
For use in finish & semi-finish applications
Balanced G2.5 @ 60,000 rpm
Bluetooth display required for operation (Sold Separately)

Typhoon
Typhoon TJS*GJET*HSK

HSK-A (DIN 69893/A)
Coolant Driven High Speed Compact Spindle
For use with small diameter tools on limited-RPM machines
Rotational Speeds of 35-55KRPM
Required Coolant Pressure 290-580psi
Maximum Tool Shank Diameter .276"/7mm
For use in finish & semi-finish applications
Balanced G2.5 @ 60,000 rpm
Bluetooth display required for operation (Sold Separately)

Typhoon
Typhoon TJS*GJET*ST

Cylindrical Straight Shank
Coolant Driven High Speed Compact Spindle
For use with small diameter tools on limited-RPM machines
Rotational Speeds of 35-55KRPM
Required Coolant Pressure 290-580psi
Maximum Tool Shank Diameter .276"/7mm
For use in finish & semi-finish applications
Balanced G2.5 @ 60,000 rpm
Bluetooth display required for operation (Sold Separately)

Typhoon
Typhoon TJS*HPC*BT

BT MAS-403
High Pressure Coolant Driven HSM Compact Spindle
For use with small diameter tools on limited-RPM machines
Rotational Speeds of 21-45KRPM
Required Coolant Pressure 217-1020psi
Maximum Tool Shank Diameter .276"/7mm
For use in finish & semi-finish applications
Balanced G2.5 @ 60,000 rpm
Bluetooth display required for operation (Sold Separately)

Typhoon
Typhoon TJS*HPC*C#

C-Adapter (ISO 26623-1)
High Pressure Coolant Driven HSM Compact Spindle
For use with small diameter tools on limited-RPM machines
Rotational Speeds of 21-45KRPM
Required Coolant Pressure 217-1020psi
Maximum Tool Shank Diameter .276"/7mm
For use in finish & semi-finish applications
Balanced G2.5 @ 60,000 rpm
Bluetooth display required for operation (Sold Separately)

Typhoon
Typhoon TJS*HPC*CAT

CAT V-Flange
High Pressure Coolant Driven HSM Compact Spindle
For use with small diameter tools on limited-RPM machines
Rotational Speeds of 21-45KRPM
Required Coolant Pressure 217-1020psi
Maximum Tool Shank Diameter .276"/7mm
For use in finish & semi-finish applications
Balanced G2.5 @ 60,000 rpm
Bluetooth display required for operation (Sold Separately)

Typhoon
Typhoon TJS*HPC*ER32

ER32 DIN 6499
High Pressure Coolant Driven HSM Compact Spindle
For use with small diameter tools on limited-RPM machines
Rotational Speeds of 21-45KRPM
Required Coolant Pressure 217-1020psi
Maximum Tool Shank Diameter .276"/7mm
For use in finish & semi-finish applications
Balanced G2.5 @ 60,000 rpm
Bluetooth display required for operation (Sold Separately)

Typhoon
Typhoon TJS*HPC*HSK

HSK-A (DIN 69893/A)
High Pressure Coolant Driven HSM Compact Spindle
For use with small diameter tools on limited-RPM machines
Rotational Speeds of 21-45KRPM
Required Coolant Pressure 217-1020psi
Maximum Tool Shank Diameter .276"/7mm
For use in finish & semi-finish applications
Balanced G2.5 @ 60,000 rpm
Bluetooth display required for operation (Sold Separately)

Typhoon
Typhoon TJS*HPC*ST

Cylindrical Straight Shank

Milling

Holemaking

Turning

Turning Grades

Turning Chipbreakers

Machining
App

RapidThread
Advisor

Product Lines

Industries

Big Cutter One - Next Stop

Big Cutter Two - Next Stop

Live
Seminars

Mobile
Seminars

Tech
Support

Customer
Service

Filter Your Results

Product Categories

Product Categories

	Show Name	Dates	Location	Website
	Motion + Power Technology Expo (formerly Gear Expo)	September 14-16, 2021	St. Louis, MO	Show Website
	South-Tec	October 26-28, 2021	Greenville, SC	Show Website

Milling

Holemaking

Turning

Turning Grades

Turning Chipbreakers

MachiningApp

RapidThreadAdvisor

Catalogs

Ingersoll TV

Product Lines

Industries

Our Most Recent Qwik-Cuts

Big Cutter One - Next Stop

Big Cutter Two - Next Stop

LiveSeminars

MobileSeminars

Our Upcoming Trade Shows

Address:

Phone or E-Mail:

TechSupport

CustomerService

Filter Your Results

Product Categories

Product Categories

Machining
App

RapidThread
Advisor

Live
Seminars

Mobile
Seminars

Tech
Support

Customer
Service